Size (length*width*height): 10cm x 10cm x 10cm

What's in the box:

1 X Devcon 10110 | 1lb Plastic Steel Putty (A)

Super Heavy Duty Devcon Steel Epoxy Putty For Industrial , Automotive , Machine Tooling

Description

The Devcon 10110 Is AGrey Putty That Comes In A1 lb Container. It Is Original Metal-Filled Epoxy Putty Used For Maintenance, Production, Tooling Applications And Bond Well To Most Metals, Concrete And Some Plastics.

It Is Applicable To Repair Areas Where Welding Or Brazing Would Be Impossible. The Putty Cures At Room Temperature And Forms ATough Durable Metallic Mass That Can Be Drilled, Tapped, Machined Or Painted.The Putty Is Excellent Resistance To Oil, Gasoline, Water And Chemicals.

Devcon 10110 Features:

Material Compatibility: Aluminum, Concrete, Metals, Plastics

Color: Gray

Primary Color: Gray

Container Size: 1lb

Coverage Area: 48in

Specific Gravity: 2.33g/cc

Maximum Operating Temperature: +90F

Minimum Operating Temperature: +55F

Applications: Filling, Rebuilding, and Bonding Metal Surfaces

Special Features:
Original Metal-Filled Epoxy Putty With Mixture Two Putty:Plastic Steel Resin And Putty Harderner
Special Used For Maintenance, Production, Tooling Applications ,Cracking ,Deep Holes
Strongly Bond Well To Most Metals, Concrete And Some Plastics.
Applicable To Repair Areas Where Welding Or Brazing Would Be Impossible.
Devcon Steel Putty Cures At Room Temperature And Forms ATough Durable Metallic Mass That Can Be Drilled, Tapped, Machined Or Painted.
Devcon Steel Putty Is Excellent Resistance To Oil, Gasoline, Water And Chemical.
Special Use In Industrial Area Such As Automotive , Industrial , Machine Tooling And Others.

Devcon 10110 Specifications:

Bonds To Most Metals, Concrete And Some Plastics

Cures At Room Temperature And Forms ATough Durable Metallic Mass That Can Be Drilled, Tapped, Machined Or Painted

Excellent Resistance To Oil, Gasoline, Water And Many Chemicals

Listed Under NSN Stock #8030-00-903-6545 #8030-00-962-4430

Direction For Use

Surface Preparation:

1. Thoroughly Clean The Surface With Devcon Cleaner Blend 300 (Devcon Cleaner Blend 300 Is Recommended For This Process) To Remove All Oil, Grease, And Dirt.

2. Grit Blast Surface Area With 8-40 Mesh Grit, Or Grind With ACoarse Wheel Or Abrasive Disc Pad, To Create Increased Surface Area For Better Adhesion (Caution: An Abrasive Disc Pad Can Only Be Used Provided White Mesh Is Revealed). Desired Profile Is 3-5mil, Including Defined Edges (Do Not Feather-Edge Epoxy). Note: For Metals Exposed To Sea Water Or Other Salt Solution, Grit-Blast And High-Pressure-Water-Blast The Area, Then Leave Overnight To Allow Any Salts In The Metal To Sweat To The Surface. Repeat Blasting To Sweat Out All Soluble Salts. Perform Chloride Contamination Test To Determine Soluble Salt Content (Should Be No More Than 40ppm).

3. Clean Surface Again With Cleaner Blend 300 To Remove All Traces Of Oil, Grease, Dust, Or Other Foreign Substances From The Grit Blasting.

4. Repair Surface As Soon AsPossible To Eliminate Any Changes Or Surface Contaminants. WORKING CONDITIONS: Ideal Application Temperature Is 55F To 90F. In Cold Working Conditions, Heat Repair Area To 100-110F Immediately Prior To Applying Epoxy To Dry Off Any Moisture, Contamination, Or Solvents, As Well As To Assist Epoxy In Achieving Maximum Adhesion Properties.

Mixing Instructions:

---- It Is Strongly Recommended That Full Units Be Mixed, As Ratios Are Pre-Measured. ----

1. Add Hardener To Resin

2. Mix Thoroughly With Screwdriver Or Similar Tool (Continuously Scrape Material Away From Sides And Bottom Of Container) Until AUniform, Streak-Free Consistency Is Obtained. INTERMEDIATE SIZES (1,2,3 lb. units): Place Resin And Hardener On AFlat, Disposable Surface Such As Cardboard, Plywood, Or Plastic Sheet). Use ATrowel Or Wide-Blade Tool To Mix The Material As In Step 2 Above. LARGE SIZES: (25 lb., 30 lb., 50 lb. Buckets): Use AT-shaped Mixing Paddle Or APropeller-Type Jiffy Mixer Model ES On An Electric Drill. Thoroughly Fold Putty By Vigorously Moving Paddle/Propeller Up And Down Until AHomogenous Mix Of Resin And Hardener Is Attained.

Application Instructions:

Spread Mixed Material On Repair Area And Work Firmly Into Substrate To Ensure Maximum Surface Contact. Plastic Steel Putty (A) Fully Cures In 16 Hours, At Which Time It Can Be Machined, Drilled, Or Painted.

FOR BRIDGING LARGE GAPS OR HOLES Place Fiberglass Sheet, Expanded Metal, Or Mechanical Fasteners Between Repair Area And Plastic Steel Putty (A) Prior To Application.

FOR VERTICAL SURFACE APPLICATIONS Plastic Steel Putty (A) Can Be Troweled Up To Thick Without Sagging.

FOR MAXIMUM PHYSICAL PROPERTIES Cure At Room Temperature For 2.5 Hours, Then Heat Cure For 4 Hours @ 200F.

FOR 70F APPLICATIONS Applying Epoxy At Temperatures Below 70F Lengthens Functional Cure And Pot Life Times. Conversely, Applying Above 70F Shortens Functional Cure And Pot Life.

MACHINING: Allow Material To Cure For At Least 16 Hours Before Machining. - Lathe Speed: 150 ft/min - Cut: Dry - Tools: Carbide Top Rake 6 (+/-2) Side/Front 8F (+/-2) - Feed Rate (rough): Travel Speed .020 Rough Cut .020 - .060 - Feed Rate (Finishing): Travel Speed .010 Finish Cut .010 - Polishing: Use 400-650 Grit Emery Paper Wet. Material Should Polish To A25-50 Micro Inch.

Proven Industrial Solution For Steel Epoxy:
Elbow Lining Repair
Chute Repair
Wear Resistant Coating
Emergency Repair
Metal Repair
Rubber Repair
Shaft Repair
Pump Repair

#Devcon#Company #Office #PlasticPutty#10110

Youtube Links:

https://www.youtube.com/watch?v=M75BIjEiCRk

Visit More On:
www.facebook.com/homewaremart